Building a Ganeti Cluster on Gentoo

Configuring DNS

Ganeti requires the following names to resolve

  • A name for the cluster as a whole, this IP must be available (cluster.example.org)
  • A name for each node (node1.example.org)
  • A name for each instance (instance1.example.org)

Building a Node

You'll probably want to configure at least two nodes as follows. Ganeti makes it easy to add or remove nodes later. Ganeti can work in a standalone mode for LVM only (no DRBD) disk storage.

DRBD Kernel

DRBD requires you to set one kernel option:

Device Drivers --->
    <*> Connector - unified userspace <-> kernelspace linker

DRBD is included in the mainline kernel in version 2.6.33 and later. You can enable it here:

Device Drivers  --->
[*] Block devices  --->
<*>   DRBD Distributed Replicated Block Device support

Go ahead and set this, recompile and reboot if necessary. If not, you still need to make sure you have the /usr/src/linux symlink updated for the kernel you are running, and (I think) run make modules_prepare.

For a normal installation with drbd compiled in:

emerge drbd

If you want to use the upstream drbd kernel modules, do the following:

emerge drbd drbd-kernel

This will pull in sys-cluster/drbd-kernel which will compile the DRBD kernel module for the kernel at /usr/src/linux. Whenever you upgrade your kernel you'll need to update the symlink and reemerge drbd-kernel. \ Now go ahead and load the drbd module

modprobe drbd minor_count=255 

If you're using DRBD 8.2.x or newer you need to use the following options:

modprobe drbd minor_count=255 usermode_helper=/bin/true
echo "drbd minor_count=255 usermode_helper=/bin/true" >> /etc/modules.autoload.d/kernel-2.6

If you have DRBD compiled as a built-in module, add the following to your kernel argument line in grub.conf:

drbd.minor_count=255 drbd.usermode_helper=/bin/true

And make sure it will be automatically loaded at boot in the future

Install Ganeti

Set the appropriate USE flags. In this case we will be using kvm. If you want an actual cluster you'll need drbd as well.

echo "app-emulation/ganeti kvm drbd" >> /etc/portage/package.use

Now go ahead and install ganeti.

emerge -av app-emulation/ganeti

Configure Networking

Ideally you should have a 'public' network that will be used for communicating with the nodes and instances from the outside, and a 'backend' network that will be used by ganeti for DRBD, migrations, etc. Assuming your 'public' IP (which node1.example.org should resolve to) is 10.1.0.11 and your 'backend' IP is 192.168.1.11, you should edit /etc/conf.d/net to look something like this:

bridge_br0="eth0"
config_eth0=( "null" )

config_br0=( "10.1.0.11 netmask 255.255.254.0" )
routes_br0=( "default gw 10.1.0.1" )

# make sure eth0 is up before configuring br0
depend_br0() {
        need net.eth0
}

config_eth1=( "192.168.1.11 netmask 255.255.255.0" )

Set the Hostname

Ganeti is picky about hostnames, and requires that the output of hostname be fully qualified. So make sure /etc/conf.d/hostname looks like this

HOSTNAME="node1.example.org"

NOT like this

HOSTNAME="node1"

Configure LVM and DRBD

“Configuring” DRBD is easy, since ganeti will do all the real work. All we need is for the service to start successfully, so just do

touch /etc/drbd.conf

It is recommended that you edit this line in /etc/lvm/lvm.conf

filter = [ "r|/dev/nbd.*|", "a/.*/", "r|/dev/drbd[0-9]+|" ]

The important part is the “r|/dev/drbd[0-9]+|” entry, which will prevent LVM from scanning drbd devices.

If you are using HP hardware raid you will also need to set preferred_names = [ “^/dev/cciss/” ]

Now, go ahead and create an LVM volume group with the disks you plan to use for instance storage. The default name that Ganeti prefers is xenvg but we recommend you choose something more useful for your infrastructure.

pvcreate /dev/cciss/c0d0p4   # Thats HP hardware raid
lvcreate xenvg /dev/cciss/c0d0p4

Building the Cluster

Initialize the Cluster

On the first node go ahead and run

gnt-cluster init -b br0 --master-netdev br0 -s [secondary-ip] \
  --enabled-hypervisors=kvm -t kvm \
  --hypervisor-parameters kvm:kernel_path:[path-to-kvm-kernel] \
  -g xenvg \
  [clustername]
  • [path-to-kvm-kernel] can be left blank if you want to supply kernels from within the guests. This can be changed later or on a per-instance basis.
  • [clustername] must resolve to an available IP address (but does not need to be a FQDN: for example ganeti where ganeti.example.org is the FQDN.). Ganeti will bring this IP address up on the master node, so you can always ssh to it.
  • [secondary-ip] this is 'private' IP mentioned previously

Adding a Node

Now you can add a second node to your cluster with

gnt-node add -s [secondary-ip] [nodename]
  • [secondary-ip] is the IP of the new node
  • [nodename] must resolve, but need not be fully qualified. For example node2 where node2.example.org is the FQDN.
 
public/ganeti/cluster_gentoo.txt · Last modified: 2011/04/27 18:08 by ramereth
 
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 3.0 Unported
Recent changes RSS feed Donate Powered by PHP Valid XHTML 1.0 Valid CSS Driven by DokuWiki